If your Chamberlain garage door opener is not working properly, or if the remote control has been misplaced or stolen, you must reset it.
I am here to assist if you’ve misplaced the source instructions, do not have any access to them, or want to take our helpful advice.
Remember that trying to reprogram a faulty garage door opener may be risky, which is why you should hire a professional.
In this article, I will address your query, How to Reset Chamberlain Garage Door Opener?
How to Reset Chamberlain Garage Door Opener?
1. Clear Your Chamberlain Garage Door Opener’s Memory
Discovering the Learn Button is the preliminary step in clearing existing programming codes as well as resetting the Chamberlain garage door opener.
That button may be found on the rear of your motor housing.

All the Chamberlain Garage Door Openers have 4 different colors of Learn button. They are
1. Yellow Learn Button
2. Purple Learn Button
3. Orange Learn Button
4. Green Learn Button
A lot of the most recent versions also have an LED light adjacent to the LEARN key. Just hold down the LEARN key for around five seconds or till the LED light turns off.
Number of Presses | Garage Door Opener Type |
1 | Security+ 2.0 (Yellow Learn Button) |
2 | Security+ (Purple Learn Button) |
3 | Security+ (Red/Orange Learn Button) |
4 | Billion Code (Green Learn Button) |
You’re remote control, as well as keyless access codes, are going to be completely wiped after the LED turns dark.
To verify that you have properly reset the opener, use the remote control that’s been programmed to the garage door opener.
The door must not engage in any way. Keep in mind that you may wish to avoid the door since it may pop open as the updated functions are being enabled.
2. Reconnect Your Remote Control
After you have reset the Chamberlain garage door opener, reconnect the controller.
The necessary actions you must complete will be determined by the type of your key as well as the color of your LEARN key on the opener.
To link your Chamberlain controller, follow the instructions below.
- Remove the metal clip from the controller. This will disclose a little key on the remote’s center.
- Hit the button using its metal clip.
- The controller will now have an LED light located on the front.
For the latest models:
- On the garage door opener, push and hold its LEARN button. The LEARN LED should turn on. Within the next thirty seconds…
- Click and hold the desired remote control key.
- Examine the garage door opener indicator light to determine whether it is blinking. If it is not, allow for the remote control lighting to settle before carefully pressing and releasing the remote control key.
- Continue till the LED bulb flashes. DO NOT push the key after the lighting has begun to flicker!
For other models:
- Next, determine the color of the LEARN key upon the Chamberlain motor housing. Push and hold the control key you want to program a few times.
- Once you’ve pushed the right number of times on the controller, hit a random key of the remote control once. The controller’s LED light must now switch off.
- Click and hold the LEARN key of the Chamberlain motor housing.
- Lastly, push the newly configured control key once, and the indicator on the opener will blink; push it once again, and the garage door will open/close!
3. Configure the Keypad
Follow the steps below to configure the keypad.
Step 1: Click the LEARN key of your Chamberlain garage door opener to set up the Chamberlain keypad.
Step 2: The LED indicator will illuminate, suggesting that you have thirty seconds to configure your keypad.
Step 3: Input the 4-digit code using your keypad, and push & hold ENTER till you notice a clicking sound and the indicator on the above Chamberlain garage door opener flashes.
Step 4: Then, hit ENTER, and the garage door will shut without issue.
Step 5: Insert the 4-digit code and click Enter when the door has closed. The garage door will be able to open.
The techniques above may help for a couple of days, but the keypad will ultimately cease functioning and may interfere with similar remote controls inside your cars.
If this applies to you, attempt the subsequent steps to configure your keypad:
- Hold down the * & # keys on your keypad till the LEDs on the keypad illuminate and afterward stop flashing.
- Click the # key after entering a fresh 4-digit password on the keypad.
- Next, hit the Enter key for the number of times that corresponds to the color of the LEARN key. For instance, if the LEARN key is yellow, hit ENTER once. To leave the programming phase, hit 0 on your keypad.
- Afterward, return to the Chamberlain garage door opener and hit the LEARN key once more. The lights on the motor housing may remain illuminated. You then got 30 seconds to complete the following step…
- Return to your keypad and input the 4-digit password once again, then push and press the ENTER key on your keypad till the indicator inside the motor housing flashes.
That must be all! You must check your keypad to ensure that it is operational.
Conclusion
In case your Chamberlain garage door opener isn’t working properly, or if you have misplaced or lost your controller, you must reset it.
To completely reset the Chamberlain garage door opener, you must:
- Clear the memory from the garage door.
- Reconnect Your Remote Control
- Configure the Keypad
If you have any problems with any of these instructions, go to Chamberlain’s webpage and look for your model’s instruction manual.
In case all else fails, contact Chamberlain customer service, and they will assist you.
FAQ
To reset any garage door, one will most likely have to unplug it or turn off the circuit that it is linked to. This will completely turn off the electricity to the door. After that, you must wait a minimum of 10 seconds until resuming electricity to the door itself.Will unplugging a garage door opener reset it?
Once the batteries in your garage door opener have been replaced, the user may be required to reset them. While this is not required for all garage door openers, several modern versions do necessitate reprogramming following battery change.Will you be required to reprogram the garage door controller following a battery change?
Last Updated on September 8, 2022 by Shabarish Balaji
- Hisense Roku TV Remote Not Working? Try These Solutions - September 24, 2023
- Hisense Roku TV Won’t Turn On? Try These Easy Solutions - September 22, 2023
- Hisense TV Black Screen? Try These Easy Solutions - September 22, 2023